How to enter the settings of the Asus router (login to the admin panel). How to enter the settings of an Asus router? Wifi router does not open asus pages
Routers or routers allow you to wirelessly connect several consumers to the Internet. Asus brand devices are widely used due to their optimal combination of price and quality. For the device to operate effectively, you need to enter the correct parameters for its operation. To do this, you will need to enter the settings of your Asus router. Let's figure out how to do this.
In addition to a personal computer or laptop, it is also possible to enter the equipment settings and adjust them using a smartphone or tablet. It is best to make changes to functional parameters during a cable connection to the consumer. Setting up your router over a wireless network may cause it to
Connecting a peripheral device to the router using the supplied cable is easy.
- One end of it is inserted into the LAN socket of the router, and the other into the corresponding computer connector according to the configuration.
- Then the router is connected to the power supply network; the main Internet cable located in the WAN connector does not need to be disconnected.
Wireless connection
The Wi-Fi network broadcast by the new router is publicly accessible; you do not need to enter a password to connect to it. In most cases it will be called Asus and an icon with the highest signal level will be placed next to it. The connection is made:
If the router has been used before or has an unknown password, you need to return it to factory settings. On the back of the case there is a hole with a small diameter, marked “RESET”. It contains a button that must be pressed and held for about 10 seconds with a thin, sharp instrument like a needle. Device parameters return to factory defaults.
Enter the router settings
In order to get into the administrative control panel of the Asus router, perform the following steps:
Step 1. The consumer connects to the device using a cable or wireless network.
Step 2. From an open browser, you enter the router settings menu. To access the router settings, you will need its IP address. You can find it out by making a cable connection or in the wireless network access menu. In addition, the login information is indicated on a sticker located on the back of the device.
On a note! Of course, if the login and password have been changed previously, new data should be entered. If they are lost, you will have to restore the router to factory settings using the method described above. The admin panel opens.
The device comes with software recorded on disk. It contains useful utilities and operating instructions. It is the easiest way to change the settings of your Asus router.
Sometimes, after performing these steps, the administrative control panel of the router does not open, but the message “page not available” appears. In this case, you should do the following:
- for a wireless connection, check the IP transmission parameters;
- if automatic address acquisition is activated and the error remains, you need to connect using a cable;
- check the integrity of its connection;
- Check the LED indication on the router case to make sure there is electrical power to the device.
In addition, you can try logging into the administrative control panel of the router using another Internet traffic consumer.
Conclusion
In conclusion, we note that entering the settings of the Asus router is not particularly difficult. By following the steps of the simple instructions, it is quite possible to do it yourself, without resorting to the help of specialists. It is better to install the firmware via a cable connection. Changes made over the wireless network may damage the equipment.
Video - How to enter settings and quickly configure an Asus router
Nowadays, many users at home have not one, but several personal computers. To ensure that every home computer (laptop, phone with WiFi support) has Internet access, you can use a router.
Different router models are configured differently, but in general:
- The router has a “WAN” socket - the cable provided to you by your Internet provider is connected there,
- Several (usually 4) “LAN” sockets - you need to connect your home computers to them.
- If the router supports a wireless WiFi connection (in this case, it comes with a small antenna), then you can connect a laptop or mobile phone (if they support WiFi technology) to it wirelessly.
Since a router is a device that provides shared network access to several devices, it must be configured to operate securely on the network, because Factory settings do not provide the required level of security and serve only to ensure the initial operation of the device.
When using a router NECESSARILY:
- change the password to access the router settings.
- set WPA or WPA2 authorization and WiFi network access key.
- change the addressing of the router's local network to 192.168.123.1 or any other not included in the network ranges 10.0.0.0-10.255.255.0, 172.16.0.0-172.22.255.0, 192.168.0.0-192.168.8.0
If you do not follow these steps, then anyone can connect to your router via WiFi and use Internet access at your expense. In addition to this, because the router divides the channel provided by the provider between everyone who is connected to it, Internet access speed of your computers will decrease depending on how actively the “guests” of your router use the Internet.
In addition, by using a router with unsafe settings, you violate the legislation of the Russian Federation and public interests protected by law, because provide communication services without the appropriate license and legal grounds, which entails administrative and/or criminal liability .
Setting up the router
1. The default setting address on Asus routers is: “192.168.1.1”
It must be entered in the address bar of the browser (Mozilla/Opera/Chrome/Internet Explorer)
Enter your login and password (Standard login: admin, password: admin)
If everything is typed correctly, you will see a picture similar to this:
2. Since the addresses: 192.168.1.x are service addresses in the Volkhov-Online LLC network and their use may interfere with the correct operation of the network, it must be changed. To do this, select "LAN" on the left. Next, change the router address, for example to “192.168.123.1”:
To save changes, click the "Apply" button
After the router reboots, you will have to reconnect to the administration page by typing the address 192.168.123.1
3. If your router has WiFi functionality, you NECESSARILY you need to configure access rules over a wireless network; to do this, go to "Wireless Network" -> "General""
In the window that appears, match the data with the images.
In the "SSID" field, enter the name of your wireless access point (any name you like, from English letters and numbers, without spaces). By this name you will find your point on a laptop or other WiFi device/
"WPA pre-shared key" you must set your own, Latin characters, numbers, and special characters (!@#$%^&*). You will use this key to connect your WiFi devices.
After completing the settings, click "Apply".
If you do not perform these actions, your point will be available to an arbitrary number of people who want to use your Internet access channel for their own purposes.
5. Setting up a connection to the Internet is done in the “WAN” -> “Internet connection” section
10. The last thing you need to do is change the password to access the router; to do this, go to the Administration->System section:
Enter a new password, confirm it and click the "Apply" button
Don't know how to log into your Asus router? I’m afraid that if I say that logging into your personal account occurs at router.asus.com or 192.168.1.1 and authorization occurs through the login and password admin-admin, then many may not understand exactly how to do this. So let's talk about everything in order. First, let's figure out how to connect it to a computer via wifi, then log into the administrator system and configure WireLess. And at the end you will find a visual video that shows the whole process in detail.
These instructions are relevant for Asus router models RT-N12, RT-N11P, RT-G32, RT-N10, RT-N10P, RT-N10U, RT-AC51U and others with a black-blue admin panel.
Logging into the Asus router via the web interface
So, before we can log into the ASUS router, we need to perform a number of steps and set a couple of configurations on the computer from which the setup will be done. Namely:
- Connect the power adapter to the router and plug it into a power outlet
- Enable "Power" button
- in “default” using the “Reset” button - it is small, located next to the antenna and recessed deep into the case. To press it, use a pin or pencil.
- Remove the Internet cable from the computer and insert it into the blue WAN connector on the router body
- Take the twisted pair cable that came with the router and connect it to the PC in place of the Internet cable. Insert it with the other end into the yellow LAN port on the router - any of the 4.
After that, go to the computer settings and find “Network Center” in the Windows “Control Panel”:
(Start - Control Panel - Network and Internet - Network and Sharing Center - Change adapter settings)
Here we find “Local Area Connection”, right-click on it and go to the “Properties > Internet Protocol Version 4” section.
We check the boxes to receive all data “automatically” and save the settings with the “OK” button.
router.asus.com - how to log into your personal account Asus 192.168.1.1?
After this, you can already log into the router. Any device has a sticker, which Asus places on the bottom of the case. You can, of course, check me and look at its contents, but I can say with my eyes closed what it says:
- Connection address - 192.168.1.1 or router.asus.com
- Login – admin
- Password - admin
Did you guess right? Otherwise! More than a dozen copies of such equipment had to be installed. If you did everything correctly in the previous step on your PC, then when you enter “ http://router.asus.com" or " http://192.168.1.1"You should be taken to the web interface of your Asus personal account. Now you can go directly to, which is the subject of a separate detailed article - read!
I can't log into the router at Router.Asus.Com
Now let's talk about what to do if you do everything according to the instructions, huh. To begin with, I advise you to immediately look at how your Internet adapter is configured on your computer or laptop. This is either a network card into which the cable is inserted, or a wireless module. Depending on what you are connecting through.
Nowadays, mostly everyone uses the Windows 10 operating system. Therefore, I will show you how to check these parameters in it.
The IP address of your ASUS personal account does not open
The error in logging into the Asus router via IP may also be due to the fact that it was once changed. That is, you are simply typing the wrong value. Finally, there is another reason why the login page to the WavLink configuration interface may not be accessible. If this is the case, then in the “Status” section you can find the same IP address that is currently listed in the router settings.
Login and password admin are not suitable
Finally, if the authorization page still opens for you, but the standard ADMIN login and password indicated on the label does not work. What to do? This tells us that they were also replaced during the previous network setup. Unfortunately, only factory settings will help here.
Video on how to log into an Asus router
This question is especially of concern to novice users, and most of all to those who recently bought a router to organize a home local network (+ Internet access for all devices in the apartment) and want to quickly set everything up...
I remember myself at that moment (4 years ago): I probably spent about 40 minutes figuring it out and setting it up. In the article I would like to dwell more not only on the question itself, but also on the errors and problems that usually arise during the process.
So, let's begin…
1. What needs to be done at the very beginning...
Buy a router... :)
The first thing you do is connect all computers to the router’s LAN ports (connect the LAN port of the router with an Ethernet cable to the LAN port of your network card).
Usually there are at least 4 LAN ports on most router models. The router comes with at least 1 Ethernet cable (regular twisted pair), which is enough for you to connect one computer. If you have more: don't forget to buy Ethernet cables at the store along with your router.
Your Ethernet cable through which you were connected to the Internet (previously it was most likely connected directly to the computer’s network card) should be plugged into the router’s socket called WAN (sometimes called Internet).
After turning on the router's power supply, the LEDs on its case should start blinking (if you have connected the cables, of course).
In principle, you can now proceed to setting up the Windows OS.
2. Determining the IP address and password with login to enter the router settings (examples ASUS, D-LINK, ZyXel)
The first setup of the router must be done on a desktop computer connected to it via an Ethernet cable. In principle, you can do it from a laptop, only then you still connect it via cable, configure it, and then you can switch to a wireless connection...
This is due to the fact that by default, the Wi-Fi network may be disabled altogether and you, in principle, will not be able to enter the router settings.
2.1. Windows OS setup
First, we need to configure the OS: in particular, the Ethernet network adapter through which the connection will go.
To do this, go to the control panel at the following path: " Control Panel\Network and Internet\Network and Sharing Center". Here we are interested in the link " Change adapter settings"(located in the left column if you have Windows 7, 8).
Go to the properties of Internet Protocol version 4.
And here you can set to automatically obtain an IP and DNS address.
Now you can go directly to the settings process itself...
2.2. How to find out the address of the router settings page
And so, launch any browser installed on your computer (Internet Explorer, Chrome, Firefox). Next, enter the IP address of your router’s settings page into the address bar. Typically this address is indicated on the documentation accompanying the device. If you don’t know, here is a small plate with popular router models. Let's look at another method below.
Table of logins and passwords (default).
If you manage to log in, you can go to the settings of your router. You may be interested in articles on setting up the following routers: , .
2.3. If you can't log in
There are two ways...
1) Go to the command line (in Windows 8, this can be done by clicking on “Win + R“, then in the “open” window that opens, enter “CMD" and press the Enter key. In other OSes, the command line can be opened through the “start” menu ").
What interests us most here is the line with the “main gateway”. It contains the address of the page with the router settings. In this case (in the picture below): 192.168.1.1 (type it into the address bar of the browser, see password and login just above).
2) If all else fails, you can simply reset the router and return it to factory settings. To do this, there is a special button on the body of the device; in order to press it you need to try: you need a pen or a knitting needle...
On the D-Link DIR-330 router, the reset button is located between the outputs for connecting the Internet and the device’s power supply. Sometimes the reset button may be located on the bottom wall of the device.
3. Conclusion
Having considered the question of how to enter the router settings, I would like to emphasize once again that usually all the necessary information is in the documents that come with the router. It’s another matter if it is written in a “barbaric” (not Russian) language and you don’t understand anything about it or you bought the router secondhand (borrowed from friends/acquaintances) and there were no pieces of paper there...
Therefore, the saying here is simple: buy a router, preferably in a store and preferably with documentation in Russian. There are now a lot of such routers and different models, the price can vary significantly, from 600-700 rubles - to 3000-4000 rubles. and higher. If you don’t know, and are just getting acquainted with such a device, I advise you to choose something in the mid-price category.
That's all. I'm going to settings...
Today we will talk about how to go into the router settings. Sometimes you need to enter the settings, but many people forget how to do this after connecting and configuring the router. In this article I will tell you how to enter various models. If you know how to enter the settings of your router but cannot do it, here is an article that describes. This article is designed for the fact that your router is already connected to the computer (if the router is not connected to the computer, read the article ““). Let's get started with the instructions.
General login instructions.
You can enter the settings using any browser. You need to enter the router address into the address bar and enter your username and password.
First, let's figure out where to get the router address. On many models, the address is written at the bottom of the label, and the login and password are also indicated there.
If you don’t have a label or don’t have access to it, you can also look in the network card settings.
On Windows XP here>>
On Windows 7 here>>
You can find out more about how to determine the router address.
Once you have determined the address of your router, enter the address into the address bar in your browser and press Enter. An Authorization window will appear in front of you, asking for Login (Username) and Password. On many models, the following settings are set by default: Login - admin, password - admin. Also look carefully at the authorization window; they sometimes write the default login and password, for example, the Zyxel company (below I will show what it looks like). After entering the data, press “Enter” and go to the settings of your router.
Let's apply this scheme on some models. The main thing that you must understand is that further we will consider the case when the router is already connected and has standard input settings. If this is not the case, then the scheme is simple: we determine the address of the router, if we changed the password and login, we remember and enter it. Also, if you couldn’t remember the changes, reset to standard settings (how to do this is described in the article “How to connect a router”), and then simply reconfigure it.
Login to router d link dir 300
This login method is also suitable for models d link dir 615, d link dir 320, d link dir 620. Enter 192.168.0.1 into the address bar of the browser (you can go to the settings of the d link dsl 2640u router at 192.168.1.1). In the window that appears, enter your login and password. If the window looks like the picture below, enter only the login-admin, leaving the password blank. :
Then click on the button. That's it, login is complete.
If, after entering the address, any of these windows opens in front of you:
in this case, the Username is admin, the password is admin. Click on the “Login” button. And you will immediately be taken to the Dlink configuration interface. If you are interested in setting up a Dlink router, then on the left side of the page in the menu, select the d link section. In it you will find a description of the setup of any model of Dlink companies.
We use this method for asus rt n10
This option is also suitable for asus rt n12, asus rt g32, asus rt n10p, asus dsl n10 routers. Open the browser and enter 192.168.1.1 in the address bar. The name is the same as on other routers, the default is admin, the password is the same. See picture below:
Once all fields have been filled in, click the “Submit” button. And you will be taken to the router settings. By selecting the ASUS section in the left column, you will find a description of the settings for various Asus models.
It’s also easy to log into the tp link tl wr741nd router
Also suitable for tp link tl wr841nd, tp link tl wr740n. Let's carry out the same steps as described above. Open the browser and enter 192.168.0.1. In the authorization window we will indicate the login and password admin and admin.
Bottom line
This scheme for entering the router settings is suitable for all models, the most important thing is to find out the login and password that you specified when setting up the router. If you haven't changed anything, then everything remains standard. Also on our website you will find many instructions and settings for various router models.
Video: What to do if you can’t access 192.168.1.1, 192.168.0.1
.
It might be useful to read:
- Cannot save the document form (invoice) in Excel format - the "Save" and "Save As" buttons are not available;
- How to clean dirt from a mouse?;
- How to enter the settings of an Asus router?;
- Electronic wallet: which one is better to choose?;
- Implementation of information systems Implementation of a new information system for an enterprise;
- How to write a claim to MTS General power of attorney MTS form;
- Optimizing your Windows 10 computer;
- Firmware for xiaomi mi 4c;